Standard Disc Springs / DIN 2093 Group A

10.005.200.50*0.75

CENTURY_SPRING model reference: CDM-105205 · CENTURY-DISC-SPRINGS-2014 · locator 16

CHRISTIAN_BAUER model reference: 104 332 · CB-DISC-SPRINGS-0611 · locator 157

MUBEA model reference: 17 0015 · MUBEA-MANUAL-2023 · printed p.60 (PDF p.62)

SCHNORR model reference: 001500 · SCHNORR-HANDBOOK-EN · locator 84

SPIROL model reference: DSC 10.0 x 5.2 x 0.50 DK · SPIROL-DISC-SPRINGS-2026 · locator 17

SPIROL model reference: DSC 10 x 5.2 x 0.5 BR · SPIROL-DISC-SPRINGS-2026 · locator 12

Dimensions, standards and downloadable engineering files are generated from published product data.

Made to order

SPECIFICATION

Product data

Open calculator →

Outside diameter De: 10.00 mm
Inside diameter Di: 5.20 mm
Product thickness t: 0.50 mm
Free height l₀: 0.75 mm
Cone height h₀: 0.25 mm
Standard: DIN 2093
Material / surface treatment: 51CrV4 Spring SteelZinc phosphate and oil · Cold presetting / scraggingERP: 10.00*5.20*0.50*0.75-T-H0.25-51CRV4-PHOSPHATE_OIL-PSX10CrNi18-8 / AISI 301 Stainless SteelPlain / natural finish · Cold presetting / scraggingERP: 10.00*5.20*0.50*0.75-T-H0.25-1.4310-PLAIN-PS60Si2MnAZinc phosphate and oil · Cold presetting / scraggingERP: 10.00*5.20*0.50*0.75-T-H0.25-60SI2MNA-PHOSPHATE_OIL-PS
Temperature: -50 – 300 °C

ENGINEERING FILES

CAD / DXF / STEP

Repository CAD · direct download

10.00*5.20*0.50*0.75 DXF and DWG engineering drawing preview

Open full drawing preview

DWG10.00*5.20*0.50*0.75 DWG CADJH-DS-10.00-5.20-0.50-0.75-P315-EN-R10.dwg · 49 KB

Download

DXF10.00*5.20*0.50*0.75 DXF CADJH-DS-10.00-5.20-0.50-0.75-P315-EN-R10.dxf · 125 KB

Download

STEP10.00*5.20*0.50*0.75 STEP CADJH-DS-10.00-5.20-0.50-0.75-P315-R10.step · 21 KB

Download

STL10.00*5.20*0.50*0.75 STL CADJH-DS-10.00-5.20-0.50-0.75-P315-R10.stl · 1.6 MB

Download

ENGINEERING OVERVIEW

Candidate decision overview

Data version 3

GEOMETRY CONTRACT

Conical profile

Bearing surfaces: No
Tolerance grade: See dossier / confirm

Special surface parameters must be reviewed against the released drawing; the profile name alone is not a complete geometry definition.

EVIDENCE COVERAGE

✓Manufacturer curve / stress6✓Polysplendid calculations1✓Resolved standards2✓Inspection dossier1—Approved product FEMNot public

A missing FEM record is not evidence of failed validation. It means no approved product-level study is public on this page.

COMBINATION BOUNDARY

Check single disc before stack

Parallel stacks primarily multiply load; series stacks primarily multiply travel. Friction, contact, guidance, preload and manufacturing scatter must be checked separately.

Stack and curves Fatigue / relaxation boundary Calculate this product

CF-07 · PROCESS CARD LIBRARY

Manufacturing process cards

5 material route(s)

Each material and supplied-surface identity has its own database-driven workbook and PNG preview. A review or blocked status is not a production release.

V13623 · R04

1.4310

PLAIN

CONTINUOUS_DIE_FORM+AUSTENITIC_COLD_WORK+NO_SUPPORT_FACE+STRONG_PRESS+PLAIN

Blocked — not for production

Download Excel · 20 kB

V4 · R04

50CrVA

BLACK_OXIDE

CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+BLACK_OXIDE

Blocked — not for production

Download Excel · 20.5 kB

V6 · R04

51CrV4

PHOSPHATE_OIL

CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+PHOSPHATE_OIL

Blocked — not for production

Download Excel · 20.2 kB

V5 · R04

60Si2MnA

BLACK_OXIDE

CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+BLACK_OXIDE

Blocked — not for production

Download Excel · 20.5 kB

V19352 · R04

60Si2MnA

PHOSPHATE_OIL

CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+PHOSPHATE_OIL

Blocked — not for production

Download Excel · 20.5 kB

APPROVED SOURCE DATA

Manufacturer engineering data

6 traceable datasets

Loads, stresses, thousand-piece weights and curves retain their manufacturer, source version, page/worksheet, material and temperature condition. A catalog value is an engineering reference unless the inspection dossier separately identifies an approved acceptance tolerance.

Century Spring / MW Industries CDM-105205Manufacturer catalog curve

Source: Century Spring Precision Disc Springs / 2014-01
Location: page 16
Material: AISI C1075 or AISI 6150 carbon/alloy steel
Temperature: Not stated - not assumed
Curve scope: four_point_curve / loading
1000-piece weight: —

Published source points only; no interpolation.

Point	s/h0	s (mm)	F (N)	σ1 / σII (MPa)	σ2 / σIII (MPa)	σ3 (MPa)	σOM (MPa)
25% h	0.250	0.0635	129	455	—	—	—
50% h	0.500	0.1270	240	876	—	—	—
75% h	0.750	0.1880	347	1,282	—	—	—
100% h	1.000	0.2515	440	1,841	—	—	—

Christian Bauer GmbH + Co. KG 104 332Manufacturer workbook calculation

Source: Christian Bauer cb_cV4 Product List / local reference edition
Location: Liste row 24
Material: Not stated in this source table
Temperature: Not stated - not assumed
Curve scope: single_point / loading
1000-piece weight: —

Point	s/h0	s (mm)	F (N)	σ1 / σII (MPa)	σ2 / σIII (MPa)	σ3 (MPa)	σOM (MPa)
75% h0	0.750	0.1875	329	—	—	—	—

Mubea 17 0015Manufacturer calculation workbook

Source: Disc Spring Calculation Program 032 / 032
Location: Standard row 17
Material: Not stated in this source table
Temperature: Not stated - not assumed
Curve scope: four_point_curve / loading
1000-piece weight: 0.225 kg

Published source points only; no interpolation.

Point	s/h0	s (mm)	F (N)	σ1 / σII (MPa)	σ2 / σIII (MPa)	σ3 (MPa)	σOM (MPa)
25% h0	0.250	0.0620	122	782	343	435	—
50% h0	0.500	0.1250	228	1,502	749	829	—
75% h0	0.750	0.1870	325	2,159	1,218	1,182	—
100% h0	1.000	0.2500	418	2,753	1,749	1,495	—

SCHNORR GmbH 001500Manufacturer catalog summary

Source: Schnorr Disc Springs Handbook / source copy in project archive
Location: page 84
Material: Not stated in this source table
Temperature: Not stated - not assumed
Curve scope: summary_only / loading
1000-piece weight: 0.214 kg

This source table publishes a summary (weight and/or σOM) but no displacement-load points; no curve has been invented.

SPIROL International Corporation DSC 10.0 x 5.2 x 0.50 DKManufacturer design calculation

Source: SPIROL Disc Springs / 2026
Location: page 17
Material: 1.4310
Temperature: Not stated - not assumed
Curve scope: five_point_curve / loading
1000-piece weight: —

Published source points only; no interpolation.

Point	s/h0	s (mm)	F (N)	σ1 / σII (MPa)	σ2 / σIII (MPa)	σ3 (MPa)	σOM (MPa)
15% h0 preload	0.160	0.0400	69	183	245	—	—
25% h0	0.240	0.0600	112	317	401	—	—
50% h0	0.520	0.1300	211	691	764	—	—
75% h0	0.760	0.1900	300	1,123	1,090	—	—
100% h0 / flat	1.000	0.2500	385	—	—	—	-1,471

SPIROL International Corporation DSC 10 x 5.2 x 0.5 BRManufacturer design calculation

Source: SPIROL Disc Springs / 2026
Location: page 12
Material: High Carbon Steel
Temperature: Not stated - not assumed
Curve scope: five_point_curve / loading
1000-piece weight: —

Published source points only; no interpolation.

Point	s/h0	s (mm)	F (N)	σ1 / σII (MPa)	σ2 / σIII (MPa)	σ3 (MPa)	σOM (MPa)
15% h0 preload	0.160	0.0400	75	198	266	—	—
25% h0	0.240	0.0600	122	343	435	—	—
50% h0	0.520	0.1300	228	749	829	—	—
75% h0	0.760	0.1900	325	1,218	1,182	—	—
100% h0 / flat	1.000	0.2500	418	—	—	—	-1,595

STANDARD DOSSIER

Resolved standard requirements

35 resolved items

PS/DS-G01-2026Polysplendid disc-spring engineering recommendations (non-mandatory)

Series A · Group 1 · without bearing surfaces

ProductRecommended edge-radius range (enterprise drawing rule)

t产品 / 6 ≤ R ≤ t产品 / 5；product limits 0.083333–0.1 mm；product recommendation 0.083333 mm；Use actual product thickness: t for plain T products and t-prime for reduced TP products. CAD defaults to the lower bound while drawings expose the full recommended range.

Disc Spring Contact Surfaces · Machinery's Handbook 31st, p.390（厂商经验转述）

ProductPolysplendid default working-deflection range

0.2–0.75 h0；product limits 0.05–0.1875 mm

聚辉推荐 DS-G01 · Mubea 2023 manual PDF 27；SPIROL deflection-range white paper

ProductNormal parallel-stack count recommendation

1–4

3.10 Spring stack design · Mubea Disc Springs Manual 2023, PDF 24

ProductSeries-stack limit for standard fatigue-chart evidence

See requirement data

10.2.2 · DIN EN 16983 page 18（PDF 20）

ProcessGuidance and stack lubrication

按温度、介质和寿命选择油、脂、含二硫化钼膏或固体润滑；不得把未润滑摩擦忽略

guidance / lubrication / friction · Mubea 2023 manual PDF 25, 28～31；Christian Bauer theory PDF 17

ProductGuidance preference

优先内导柱；空间或结构要求时使用外导套；低迟滞需求评估自定心结构

C.1 / 3.10 · GB/T 1972.2 附录 C；Mubea 2023 manual PDF 24～25

ProductGeometry triggers for enhanced analysis

De/Di=1.923077，De/t=20，within simplified-geometry range

3.9 Special cases · Mubea Disc Springs Manual 2023, PDF 21

DIN EN 16983:2017-09Disc springs — Quality specifications — Dimensions

Series A · Group 1 · without bearing surfaces

ProductDisc spring group 1

Table 2 · EN 16983 pages 6～7（PDF 8～9）

ProductDimension series A

Table 3 · EN 16983 pages 6～7（PDF 8～9）

ProductStandard spring steel requirement

EN 10083 / EN 10089 / EN 10132-4 MPa

5 · EN 16983 page 7（PDF 9）

ProcessGroup 1 manufacturing and surface finish

冲压、冷成形、边缘倒圆

Table 7 · EN 16983 page 11（PDF 13）

ProductThickness tolerance

deviation -0.06 / +0.02 mm；product limits 0.44–0.52 mm

Table 8 · EN 16983 page 13（PDF 15）

ProductOutside diameter h12 tolerance

deviation -0.15 / 0 mm；product limits 9.85–10 mm；h12

8.1 / ISO 286-2 · EN 16983 page 12（PDF 14）

ProductInside diameter H12 tolerance

deviation 0 / +0.12 mm；product limits 5.2–5.32 mm；H12

8.1 / ISO 286-2 · EN 16983 page 12（PDF 14）

ProductFree-height tolerance

deviation -0.05 / +0.1 mm；product limits 0.7–0.85 mm

Table 9 · EN 16983 page 13（PDF 15）

ProductTest-load tolerance

deviation -7.5 / +25 %；test position 0.75 h0

Table 10 · EN 16983 pages 13～14（PDF 15～16）

ProductCoaxiality tolerance

0.18 mm；2 × IT11

8.1 / ISO 286-2 · EN 16983 page 12（PDF 14）

InspectionGroup 1 / series A minimum unloading-force ratio

See requirement data

Table 11 · EN 16983 page 15（PDF 17）

ProductGroup 1 hardness

425–510 HV10

7.2 · EN 16983 page 11（PDF 13）

ProductRecommended total clearance for guide pin

0.2 mm；recommended guide pin diameter 5 mm

Table 12 · EN 16983 page 15（PDF 17）

ProductRecommended total clearance for guide sleeve

0.2 mm；recommended guide sleeve bore 10.2 mm

Table 12 · EN 16983 page 15（PDF 17）

ProductGuide component surface requirement

See requirement data

12 · EN 16983 section 12, page 21（PDF 23）

ProcessPresetting

2 × test load；压至平位后复核自由高度与检测负荷

7.4 / 8.4.2 · EN 16983 pages 12, 14（PDF 14, 16）

ProcessSurface quality and edges

无影响性能的斑疤、裂纹、锈蚀；边缘倒圆或去毛刺

7.5 · EN 16983 page 12（PDF 14）

ProcessSurface treatment and corrosion protection

phosphated and oiled

7.5 · EN 16983 page 12（PDF 14）

ProcessShot peening

recommended for dynamic duty where fatigue-life improvement is required；process agreement required

10.2.2 · EN 16983 page 20（PDF 22）

InspectionDecarburization depth

product maximum depth 0.015 mm

7.2 · EN 16983 page 11（PDF 13）

ProductStatic calculated stress limit

See requirement data

10.1 · EN 16983 page 17（PDF 19）

ProductMinimum preload for dynamic duty

0.15–0.2 h0；product limits 0.0375–0.05 mm

10.2.1 · EN 16983 page 18（PDF 20）

ProductRelaxation and operating-temperature note

Consult the manufacturer above 100 °C for material, stress and relaxation requirements

9 / Figures 3–4 · EN 16983 page 17（PDF 19）

InspectionTest-load method

test position 0.75 h0；硬化、磨削并抛光的压盘；使用适合润滑剂

8.4.1 · EN 16983 page 13（PDF 15）

InspectionDimensional inspection method

按标准约定的量具、压盘及测量条件执行

8 · EN 16983 pages 13～14（PDF 15～16）

InspectionHardness test method and location

See requirement data

11.3 · EN 16983 page 21（PDF 23）

BatchBatch sampling and acceptance

Acceptance inspection according to EN ISO 3269 where applicable

2 · EN 16983 pages 11～18（PDF 13～20）

PackagingMarking, packaging and storage

Contract and product documentation requirements apply

contract · EN 16983 pages 11～18（PDF 13～20）

INSPECTION DOSSIER

Product inspection requirements

7 acceptance limits

Data boundary: 平面度没有标准通用数值，等待图纸/工艺卡/供需协议覆盖; 平行度没有标准通用数值，等待图纸/工艺卡/供需协议覆盖

Characteristic	Requirement / limits	Status	Source
Outside diameterD / De	10 mm (-0.15/+0 mm); limits 9.85–10 mmThe standard rule has been resolved for this specific product.	Resolved	DIN EN 16983:2017-09EN 16983 page 12（PDF 14）
Inside diameterd / Di	5.2 mm (+0/+0.12 mm); limits 5.2–5.32 mmThe standard rule has been resolved for this specific product.	Resolved	DIN EN 16983:2017-09EN 16983 page 12（PDF 14）
Product thicknesst / t′	0.5 mm (-0.06/+0.02 mm); limits 0.44–0.52 mmThe standard rule has been resolved for this specific product.	Resolved	DIN EN 16983:2017-09EN 16983 page 13（PDF 15）
Free heightH0 / l₀	0.75 mm (-0.05/+0.1 mm); limits 0.7–0.85 mmThe standard rule has been resolved for this specific product.	Resolved	DIN EN 16983:2017-09EN 16983 page 13（PDF 15）
Cone heighth0 / h₀	0.25 mm (-0.07/+0.16 mm); limits 0.18–0.41 mmWorst-case envelope derived from free-height and plain product thickness t tolerances; it is a reference, not an independent standard h0 acceptance tolerance.	Derived reference	DIN-EN-16983-2017-09EN 16983 page 13（PDF 15）; EN 16983 page 13（PDF 15）
Coaxiality—	≤ 0.18 mmThe standard rule has been resolved for this specific product.	Resolved	DIN EN 16983:2017-09EN 16983 page 12（PDF 14）
Flatness—	Set by approved drawing, process card or supply agreementThe standard does not provide a universal independent numeric tolerance; an approved drawing, process card or supply agreement must provide the acceptance value.	Agreement required	POLYSPLENDID-INSPECTION-POLICY-2026-08Task 121 标准原文核对结论
Parallelism—	Set by approved drawing, process card or supply agreementThe standard does not provide a universal independent numeric tolerance; an approved drawing, process card or supply agreement must provide the acceptance value.	Agreement required	POLYSPLENDID-INSPECTION-POLICY-2026-08Task 121 标准原文核对结论
Test loadFt	325 N (-7.5/+25%); limits 300.625–406.25 NThe nominal test load comes from the current published standard, manufacturer, or engineering dataset; limits use the applicable DIN EN 16983 percentage tolerance.	Resolved	DIN EN 16983:2017-09EN 16983 pages 13～14（PDF 15～16）
Hardness—	425–510 HV10The standard rule has been resolved for this specific product.	Resolved	DIN EN 16983:2017-09EN 16983 page 11（PDF 13）

Where cone-height limits are shown, they are derived references only. Flatness and parallelism become acceptance criteria only after an approved drawing, process card or supply agreement supplies numeric values.

ENGINEERING SERVICE

Review this specification for your application

Request a quote →