Standard Disc Springs / DIN 2093 Group C
CENTURY_SPRING model reference: CDM-633118 · CENTURY-DISC-SPRINGS-2014 · locator 18
CHRISTIAN_BAUER model reference: 104 868 · CB-DISC-SPRINGS-0611 · locator 162
MUBEA model reference: 18 0067 · MUBEA-MANUAL-2023 · printed p.66 (PDF p.68)
SCHNORR model reference: 016050 · SCHNORR-HANDBOOK-EN · locator 92
SOLON model reference: SDS 63x31x1.8 · SOLON-BELLEVILLE-CATALOG · locator 52
SPIROL model reference: DSC 63 x 31 x 1.8 WR · SPIROL-DISC-SPRINGS-2026 · locator 16
Dimensions, standards and downloadable engineering files are generated from published product data.
Open full drawing previewSpecial surface parameters must be reviewed against the released drawing; the profile name alone is not a complete geometry definition.
A missing FEM record is not evidence of failed validation. It means no approved product-level study is public on this page.
Parallel stacks primarily multiply load; series stacks primarily multiply travel. Friction, contact, guidance, preload and manufacturing scatter must be checked separately.
Each material and supplied-surface identity has its own database-driven workbook and PNG preview. A review or blocked status is not a production release.
BLACK_OXIDE
CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+BLACK_OXIDE
Blocked — not for production
Download Excel · 20.7 kB
PHOSPHATE_OIL
CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+PHOSPHATE_OIL
Blocked — not for production
Download Excel · 20.4 kB
BLACK_OXIDE
CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+BLACK_OXIDE
Blocked — not for production
Download Excel · 20.7 kB
PHOSPHATE_OIL
CONTINUOUS_DIE_FORM+LOW_ALLOY_QT+NO_SUPPORT_FACE+STRONG_PRESS+PHOSPHATE_OIL
Blocked — not for production
Download Excel · 20.7 kBLoads, stresses, thousand-piece weights and curves retain their manufacturer, source version, page/worksheet, material and temperature condition. A catalog value is an engineering reference unless the inspection dossier separately identifies an approved acceptance tolerance.
| Point | s/h0 | s (mm) | F (N) | σ1 / σII (MPa) | σ2 / σIII (MPa) | σ3 (MPa) | σOM (MPa) |
|---|---|---|---|---|---|---|---|
| 25% h | 0.250 | 0.5918 | 2,504 | 558 | — | — | — |
| 50% h | 0.500 | 1.1862 | 3,866 | 1,034 | — | — | — |
| 75% h | 0.750 | 1.7780 | 4,466 | 1,420 | — | — | — |
| 100% h | 1.000 | 2.3698 | 4,688 | 1,710 | — | — | — |
| Point | s/h0 | s (mm) | F (N) | σ1 / σII (MPa) | σ2 / σIII (MPa) | σ3 (MPa) | σOM (MPa) |
|---|---|---|---|---|---|---|---|
| 75% h0 | 0.750 | 1.7625 | 4,237 | — | — | — | — |
| Point | s/h0 | s (mm) | F (N) | σ1 / σII (MPa) | σ2 / σIII (MPa) | σ3 (MPa) | σOM (MPa) |
|---|---|---|---|---|---|---|---|
| 25% h0 | 0.250 | 0.5870 | 2,364 | 961 | -4 | 536 | — |
| 50% h0 | 0.500 | 1.1750 | 3,658 | 1,785 | 130 | 986 | — |
| 75% h0 | 0.750 | 1.7620 | 4,238 | 2,470 | 402 | 1,351 | — |
| 100% h0 | 1.000 | 2.3500 | 4,463 | 3,018 | 811 | 1,629 | — |
This source table publishes a summary (weight and/or σOM) but no displacement-load points; no curve has been invented.
| Point | s/h0 | s (mm) | F (N) | σ1 / σII (MPa) | σ2 / σIII (MPa) | σ3 (MPa) | σOM (MPa) |
|---|---|---|---|---|---|---|---|
| catalog listed operating point | 1.005 | 2.3620 | 4,463 | — | — | — | — |
| Point | s/h0 | s (mm) | F (N) | σ1 / σII (MPa) | σ2 / σIII (MPa) | σ3 (MPa) | σOM (MPa) |
|---|---|---|---|---|---|---|---|
| 15% h0 preload | 0.149 | 0.3500 | 1,566 | -19 | 332 | — | — |
| 25% h0 | 0.251 | 0.5900 | 2,364 | -4 | 536 | — | — |
| 50% h0 | 0.502 | 1.1800 | 3,658 | 130 | 986 | — | — |
| 75% h0 | 0.749 | 1.7600 | 4,238 | 402 | 1,351 | — | — |
| 100% h0 / flat | 1.000 | 2.3500 | 4,463 | — | — | — | -1,315 |
t产品 / 6 ≤ R ≤ t产品 / 5；product limits 0.3–0.36 mm；product recommendation 0.3 mm；Use actual product thickness: t for plain T products and t-prime for reduced TP products. CAD defaults to the lower bound while drawings expose the full recommended range.
Disc Spring Contact Surfaces · Machinery's Handbook 31st, p.390（厂商经验转述）0.2–0.75 h0；product limits 0.47–1.7625 mm
聚辉推荐 DS-G01 · Mubea 2023 manual PDF 27；SPIROL deflection-range white paper1–4
3.10 Spring stack design · Mubea Disc Springs Manual 2023, PDF 24See requirement data
10.2.2 · DIN EN 16983 page 18（PDF 20）按温度、介质和寿命选择油、脂、含二硫化钼膏或固体润滑；不得把未润滑摩擦忽略
guidance / lubrication / friction · Mubea 2023 manual PDF 25, 28～31；Christian Bauer theory PDF 17优先内导柱；空间或结构要求时使用外导套；低迟滞需求评估自定心结构
C.1 / 3.10 · GB/T 1972.2 附录 C；Mubea 2023 manual PDF 24～25De/Di=2.032258，De/t=35，within simplified-geometry range
3.9 Special cases · Mubea Disc Springs Manual 2023, PDF 212
Table 2 · EN 16983 pages 6～7（PDF 8～9）C
Table 3 · EN 16983 pages 6～7（PDF 8～9）EN 10083 / EN 10089 / EN 10132-4 MPa
5 · EN 16983 page 7（PDF 9）冲压/精冲、冷成形、内外径加工、边缘倒圆
Table 7 · EN 16983 page 11（PDF 13）deviation -0.12 / +0.04 mm；product limits 1.68–1.84 mm
Table 8 · EN 16983 page 13（PDF 15）deviation -0.3 / 0 mm；product limits 62.7–63 mm；h12
8.1 / ISO 286-2 · EN 16983 page 12（PDF 14）deviation 0 / +0.25 mm；product limits 31–31.25 mm；H12
8.1 / ISO 286-2 · EN 16983 page 12（PDF 14）deviation -0.08 / +0.15 mm；product limits 4.07–4.3 mm
Table 9 · EN 16983 page 13（PDF 15）deviation -7.5 / +15 %；test position 0.75 h0
Table 10 · EN 16983 pages 13～14（PDF 15～16）0.6 mm；2 × IT12
8.1 / ISO 286-2 · EN 16983 page 12（PDF 14）See requirement data
Table 11 · EN 16983 page 15（PDF 17）42–52 HRC
7.2 · EN 16983 page 11（PDF 13）0.5 mm；recommended guide pin diameter 30.5 mm
Table 12 · EN 16983 page 15（PDF 17）0.8 mm；recommended guide sleeve bore 63.8 mm
Table 12 · EN 16983 page 15（PDF 17）See requirement data
12 · EN 16983 section 12, page 21（PDF 23）2 × test load；压至平位后复核自由高度与检测负荷
7.4 / 8.4.2 · EN 16983 pages 12, 14（PDF 14, 16）无影响性能的斑疤、裂纹、锈蚀；边缘倒圆或去毛刺
7.5 · EN 16983 page 12（PDF 14）phosphated and oiled
7.5 · EN 16983 page 12（PDF 14）recommended for dynamic duty where fatigue-life improvement is required；process agreement required
10.2.2 · EN 16983 page 20（PDF 22）product maximum depth 0.054 mm
7.2 · EN 16983 page 11（PDF 13）See requirement data
10.1 · EN 16983 page 17（PDF 19）0.15–0.2 h0；product limits 0.3525–0.47 mm
10.2.1 · EN 16983 page 18（PDF 20）Consult the manufacturer above 100 °C for material, stress and relaxation requirements
9 / Figures 3–4 · EN 16983 page 17（PDF 19）test position 0.75 h0；硬化、磨削并抛光的压盘；使用适合润滑剂
8.4.1 · EN 16983 page 13（PDF 15）按标准约定的量具、压盘及测量条件执行
8 · EN 16983 pages 13～14（PDF 15～16）See requirement data
11.3 · EN 16983 page 21（PDF 23）Acceptance inspection according to EN ISO 3269 where applicable
2 · EN 16983 pages 11～18（PDF 13～20）Contract and product documentation requirements apply
contract · EN 16983 pages 11～18（PDF 13～20）| Characteristic | Requirement / limits | Status | Source |
|---|---|---|---|
| Outside diameterD / De | 63 mm (-0.3/+0 mm); limits 62.7–63 mmThe standard rule has been resolved for this specific product. | Resolved | DIN EN 16983:2017-09EN 16983 page 12（PDF 14） |
| Inside diameterd / Di | 31 mm (+0/+0.25 mm); limits 31–31.25 mmThe standard rule has been resolved for this specific product. | Resolved | DIN EN 16983:2017-09EN 16983 page 12（PDF 14） |
| Product thicknesst / t′ | 1.8 mm (-0.12/+0.04 mm); limits 1.68–1.84 mmThe standard rule has been resolved for this specific product. | Resolved | DIN EN 16983:2017-09EN 16983 page 13（PDF 15） |
| Free heightH0 / l₀ | 4.15 mm (-0.08/+0.15 mm); limits 4.07–4.3 mmThe standard rule has been resolved for this specific product. | Resolved | DIN EN 16983:2017-09EN 16983 page 13（PDF 15） |
| Cone heighth0 / h₀ | 2.35 mm (-0.12/+0.27 mm); limits 2.23–2.62 mmWorst-case envelope derived from free-height and plain product thickness t tolerances; it is a reference, not an independent standard h0 acceptance tolerance. | Derived reference | DIN-EN-16983-2017-09EN 16983 page 13（PDF 15）; EN 16983 page 13（PDF 15） |
| Coaxiality— | ≤ 0.6 mmThe standard rule has been resolved for this specific product. | Resolved | DIN EN 16983:2017-09EN 16983 page 12（PDF 14） |
| Flatness— | Set by approved drawing, process card or supply agreementThe standard does not provide a universal independent numeric tolerance; an approved drawing, process card or supply agreement must provide the acceptance value. | Agreement required | POLYSPLENDID-INSPECTION-POLICY-2026-08Task 121 标准原文核对结论 |
| Parallelism— | Set by approved drawing, process card or supply agreementThe standard does not provide a universal independent numeric tolerance; an approved drawing, process card or supply agreement must provide the acceptance value. | Agreement required | POLYSPLENDID-INSPECTION-POLICY-2026-08Task 121 标准原文核对结论 |
| Test loadFt | 4240 N (-7.5/+15%); limits 3922–4876 NThe nominal test load comes from the current published standard, manufacturer, or engineering dataset; limits use the applicable DIN EN 16983 percentage tolerance. | Resolved | DIN EN 16983:2017-09EN 16983 pages 13～14（PDF 15～16） |
| Hardness— | 42–52 HRCThe standard rule has been resolved for this specific product. | Resolved | DIN EN 16983:2017-09EN 16983 page 11（PDF 13） |
Where cone-height limits are shown, they are derived references only. Flatness and parallelism become acceptance criteria only after an approved drawing, process card or supply agreement supplies numeric values.
ENGINEERING SERVICE